Search results for 'synch'
-
Synchronizing Tool STE-BK
Sku: STE-BK
The STE BK will fit intakes of approx. 2” to about 2 5/8”. The BK features a rubber sleeve that can be rotated to open a by-pass allowing a higher air flow up to 50 kg/h; by-pass closed 1 to 35 kg/h. Using an additional adapter STE 118 will allow the BK to fit intakes as small as 1 ½” similar to the STE SK and allow for higher RPM air flow and synchronization. (Most universal combination) Learn More$79.00 -
48 IDF Kit
Sku: v8_ford_0002
Quad 44IDF and 48IDF Kits for FORD 289 and 302. Thermostat Housing style manifold ONLY. No dual water pipe Cobra manifolds for IDF's Complete assembled kits with 4 New WEBER IDF Carbs, Linkage, Air Horns and Synch Tool
INCLUDES SS FUEL LINE SET !
* $40 Shipping and Insurance in the Lower 48 States for all V8 Kits
* AK, HI, PR and International Shipments pay actual shipping costs.For Street Application 302 and 289 engines making at or under 425HP I highly recommend you consider the 44IDF kits and the IDF kits in general ove the IDA's. They are more streetable and more easily tuned.
Learn More$3,395.00 -
Quad 48 IDA Weber Conversion for289 / 302 / 347 FORD SMALL BLOCK
Sku: v8_ford_0003
Quad 48 IDA Weber Conversion for289 / 302 / 347 FORD SMALL BLOCK Learn More$3,995.00 -
Quad 48IDA Weber Conversion for 351 Windsor FORD
Sku: v8_ford_0005
4 x 48 IDA Weber Carbs (made in Spain) modified for low to mid RPM drivability SS Fuel Lines included
Learn More
Weber Tuning Manual and Synchrometer included...This kit is assembled and Ready to install.
$4,850.00 -
Quad 48IDA Weber Conversion for 351 Cleveland FORD
Sku: v8_ford_0007
Quad 48IDA Weber Conversion for 351 Cleveland FORD Learn More$4,795.00 -
Quad 48IDA Weber Conversion for 427 Ford
Sku: v8_ford_0008
Quad 48IDA Weber Conversion for 427 Ford Learn More$4,295.00 -
Quad 48IDA Weber Conversion for 429/460 Ford V-8
Sku: v8_ford_0009
Quad 48IDA Weber Conversion for 429/460 Ford V-8 Learn More$0.00 -
Small Block 48 IDF Quad Weber Kit Complete assembly.
Sku: K9402-8
COMPLETE KIT. SEE BELOW FOR OPTIONS AND UPGRADES.
Learn More
Small Block 48 IDF s Complete assemblyAll V8 Max Pac kits are pre jetted, pre assembled then bench flow tested and adjusted for quick start and tune.
Includes Synch Tool and SS Fuel Line Set.
$40 Shipping in the Lower 48 states$3,495.00 -
Peter Fritsche Quad 48IDA Weber Conversion for 429/460 Ford V-8
Sku: Peter_Fritsche_460Kit
4 x 48 IDA Weber Conversion for Ford 429/460 V8 Engines. Kit consists of 4 New Weber 48 IDA Carburetors, Intake Manifold and Linkage,
Synchrometer included. This kit is assembled and Ready to install. Picture of actual conversion not available, 427 model is shown.Includes Custom Jetting Kit for 600 HP which is + $295
Learn More
$40 Shpping to TX Insured.$4,295.00 -
LINKAGE KIT, DGV synchronise primary & secondary barrels
Sku: SYNC-LINK
Linkage Kit Learn More$42.95 -
Synchronizing Tool STE 8
Sku: STE 8
Large opening: Use with STE BK and STE SK Smaller opening: Use adapter STE 18 for multiple inlets, 40 -55 DCOE 2 ¼” max. Learn More$23.73 -
Synchronizing Tool STE 6
Sku: STE 6
Large opening: Use with STE BK and STE SK Smaller opening: Perfectly fits into 40-DCOE inlets, 1 9/16” Alpha, Solex, Weber Learn More$28.00 -
Synchronizing Tool STE-SK
Sku: STE-SK
The STE SK will fit intakes of 1 5/8” to 2 1/8”. This SK will measure air flow from 1 to 30 kg/h. With this “lower” calibration scale it is easier to read the variations in air flow between carburetors at idle RPM’s only. The SK also has extended calibration at 1 to 3 kg/h also making it useful to check secondary throttle adjustment at idle. Learn More$63.95 -
Synchronizing Tool STE 1
Sku: STE 1
Inside Diameter: 5 3/8” Inside Height: 1 9/16” Use with BK & SK Zenith 35 40 INAT Learn More$13.95 -
Synchronizing Tool STE 118
Sku: STE 118
Taper 1 7/16” O.D. 1 ½” O.D. 2 ¼” Use with STE BK Learn More$21.95 -
Synchronizing Tool STE 13
Sku: STE 13
Top: O.D. 2” I.D. 1 9/16” Bottom: O.D. 1 ¾” I.D. 1 7/16” Use with STE BK and STE SK Height 1 ¾” Learn More$10.32 -
Synchronizing Tool STE 18
Sku: STE 18
O.D. 1 1/8” O.D. 2 ¼” Use with BK & SK or STE 8, DCO Learn More$19.95 -
Synchronizing Tool STE 25
Sku: STE 25
Male to Inlet w/taper1 7/8” 44-IDF, 45-DCOE Use with STE BK and STE SK Learn More$23.44 -
Synchronizing Tool STE 28
Sku: STE 28
Male to Inlet 2” 48-IDF, 48-IDA, 48-DCOE Use with STE BK and STE SK Learn More$9.32