S14

4 Cylinder JE Custom Forged Piston Set - All Flat Top - with or without valve pockets
ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings.
Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder M42 / M44 JE Custom Forged Piston Set - All Compression Ratios

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder JE Custom Forged Piston Set - Remake from 2006 Job for 500HP and NOS

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder JE Custom Forged Piston Set - All Dome Top - with or without valve pockets

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder JE Custom Forged Piston Set -

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

Subaru EJ205 96mm x 79mm x 8.5

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

PRICE INCLUDES SHIPPING !!!

Order from 09-2013
BMW S14 M3 2.3 12:1 N/A 8000 RPM
94mm x 84mm x 40.2cc head x 1.69mm HG x .89mm + Deck
PO# Bernard

From 94mm you need to go to 94.5mm to get a proper ring set…
There are no proper rings at 94.20 or 94.25mm
We would want to keep the same material and ring pack style as you have been using to insure long life…

That is a safe bore size for that block….

Set of 4 Pistons exactly like the set from 09-13
94.5mm bore…
Asymetric FSR with .5mm Pin Offset.
Total Seal Gapless Top Rings
Pin Fit for use with the Same Pins
New Pin Locs
Lateral Gas Ports

Tuff Skirt Coat
Contact Reduction Grooves

$981.45 + $99 UPS To Germany

Learn More

4 Cylinder JE Custom Forged Piston Set - All Dome Top - SHIPPING IS INCLUDED IN THIS PRICE !

93 Series Pins and Skirt Coatings + Skirt Notch + Extra Ring Set for 81.5mm bore set.1 x 1.2 x 2.8

Final changes, compress rate 10:1, vr has to be 4 mm wider and 3 mm deeper (my valves are 4 mm bigger than stocks) same skirt notch works very well, New notch dimensions are: Y=51 mm, W=28 mm, X=11 mm.
90 mm stroke is correct, my new head gasket is compressed to 1.37 mm. 93 series pins is the ones that I want. Master card payment as usually and a low value receipt including shipment? Same shipment as usually.

I am building a new engine with Darton sleves with 83 mm boore and hoping to get over 1000 hp
I would like to order four JE pistons for Volvo, size 83 mm. (1948 cm3)
Bore 83.00mm, Comp height 1.413, forging 83M, Pin dia .905, Pin length 2.250,
To the exhaust side of the pistons there should be one "hole" for the oil injector. compression rate 10.0:1
The combustion chamber is 50 cc. 

My address is:
Conny Lindroos
Heinäkuja 1
21380 Aura Finland
+358 400828519

Learn More

$695 01 Set of JE 11:1 CR pistons in 94mm ( Perfect ) (unless you specify larger bore as measured is 93.40mm)
$885 01 Set Of Pauter Rods
$143 01 Cometic HG (thickness? Not sure as the head has 95.41mm height & block height of 277.66 mm )
I will make the piston correct for use with a .051 Head Gasket…
$97.20 01 Oil Pan Baffle
$840 Supertech Kit
----------
$2660.21 US Parts Total
$40 Shipping and insrance
----------
$2700.21 US

If you are using an International Credit Card there will be an additional 2.5% Intl CC Fee $67.50
Intl. PayPal will incur a 3% Intl PayPal fee..$81.00

Shipped to::
8378 NW 68 Street Miami, FL 33166.

Thanks
Steve

Learn More

JE Custom Cosworth YB Set for Long Rods with Spiralocs New rod measure 136.5mm center - center. New piston needs a compression height of 32mm. I also remove the 0.8mm from compression height since the block is decked. Bore size is 91.00mm. Piston wrist pin is 24mm. Piston needs valve pockets to be 2mm deep. 32mm exhaust valve 36.5mm inlet valve New desired comp ratio should be around 7.5-7.6. Head volume is 42cc and gasket thickness is 1.3mm. Learn More

My engine has the Motorsport DTM crank @ 87mm stroke that is lighter than the road 2.5 litre unit It has H beam rods @ 144 mm long, piston oil squirters, 8 injector slide throttle, 324 / 308 cams with 13mm lift, 39mm / 32.5mm inlet, exhaust valves. Also the engine revs to 9700 and it runs on 100 octane leaded race fuel. I need a comp ratio of no less than 12.5 to 1 and max 12.8.

4 Cylinder JE Custom Forged Piston Set - All Dome Top - with or without valve pockets
ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings.
Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder JE Custom Forged Piston Set - All Dome Top - with or without valve pockets

ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings

Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More

4 Cylinder JE Custom Forged Piston Set - All Dish Top - with or without valve pockets
ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings.
Please note: ALL JE Custom Pistons take 3 weeks to make + 1 week for any coating operations

Learn More