Datsun Z-510
Welcome to the Top-End Performance Nissan / Datsun Site...With over 25 years of hands-on performance experience with Z cars and 510's we are the most experienced performance shop of our kind for these cars...Weber carbs to complete programmable engine management systems...Normally Aspirated or Turbocharged, Valve jobs to complete race engines, Bushings to complete 4 corner coil-over systems and Big Brake Converions, A tune up to a complete mechanical restoration...
We are THE PLACE for Triple Weber Carbs and TWM-BORLA ITB Packages...
See this Page
- Z car Suspension Components and Bushings
- Z Car Triple Sidedraft Weber Carb and Fuel Injection Conversions
- Datsun Z Car and 510 Engine building.
- 240Z-280Z Car Front Ultimate Strut Tower Brace
- 240Z-280Z Car Rear Ultimate Strut Tower Brace
- Datsun Headers
- Z Car "L" Series Triple Webers and Triple TWM - BORLA ITB Systems
-
JE Forged Piston Set for Datsun L24-L28 Engines. Flat or Dish with Valve Pockets.
SKU: L24_L26_L28_JE-Pistons6 Cylinder JE Custom Forged Piston Set - Dish, Flat or Dome - with or without valve pockets
ALL JE Forged Piston Sets are Supplied complete with Pins Locs and JE ProSeal Rings
Please note: ALL JE Custom Pistons are currently 7-8 Week lead time to make
Learn More$1,395.00 -
Longlom Thailand 3TC Pistons and Push Rods
SKU: Longlom_L28_Thailand3TC Pistons in 11.5:1 will be a Custom made to order set onlyLearn More
$895 set of 4 with Pins, Locs and Rings...PLEASE SPECIFY BORE
Chromoly 3TC Pushrods are $149 for the set of 8
+ Shipping to be sorted out when ready to go...$1,044.00 -
Longlom Thailand Z Car Parts Package
SKU: Z_Custom_EngineKit1. Compression ratio is 11:1 or 10.75,I will play around with custom head gasket. We have ron95 here.2. The head is N423. Expected HP should be close to 300hp at flywheel.
4. Camshaft is Tomei 290’ with 8.80mm camlift.Delivery address is :
Ms Supatra Eamporn
2/289 Anusaowareechai Condo, Phaholyothin Road Soi 2/1, Samsennai, Phayathai, Bangkok 10400
Tel +66894453584 or +66818332768> Large Tube 1.625" Race Header for High Compression 3.0+
$399
> 1. A set of DOMED JE pistons 88mm with coating skirt and valve pockets.
$1050 + $138 Skirt Coat depending on Dome, Dish, Flat, etc.
That is a set of 6 Forged JE Pistons with Pins, Locs and JE Pro-Seal Rings.
> 2. A set of Conrod for using with LD28 crankshaft.
No problem 133mm H-Beam Rods with ARP2000 Bolts
$650
> 3. A set of racing valve largest possible 46mm inlet or larger. !
46mm Intake and 38mm Exhaust
$250 Set of 12
> 4. A set of valve spring
with Matching Moly Steel Retainers. No Titanium
$ 215 for the full set...
> 5. A set of valve guide ,silicone bronze if possible.
$9.50 each = $114
----------
$2816
$345
----------
$3161 US$3,161.00