Toyota 7MGT Upgrades

 

In our opinion the Toyota 7MGT engine is the absolute best powerplant available. You can make huge amounts of HP reliably if not cheaply. Low 12. s and high11. s from a early body style Supra is very common and not very hard to do. The down side to this engine is there is very little bolt on equipment that makes much difference. You need to jump right in and do the big stuff. Sure, you can do and air filter, exhaust, EVC, Etc. but the real power comes from serious Turbo and fuel system upgrades. Along with these mods the internal engine pieces must also be upgraded to withstand the extra heat and stress.

Our standard street buildup is about 500 HP on pump gas and 600+ on race fuel. Internal Engine work is fairly straightforward and all pieces are readily available. The Turbo and fuel system is a bit more complex. The stock management system even with an AIC cannot support much more than

425 -450hp because of the Air flow meter restriction. We use aftermarket Speed Density Metering management such as the Electromotive TEC-II, the HALTECH F9A, or the HALTECH E6

The stock ignition system and timing curve is also very good for most street applications once you have control of the fuel and eliminate the air flow meter. To keep the stock ignition and eliminate the fuel only you would use the HALTECH F9A system.

 

Toyota 7MGT Engine Buildup for 600+ HP applications:

Block Components:

JE 7.5:1 Compression Pistons. .030 overbore.            ( set of 6 )   $825.00                  

 

Optional: Ceramic Coated tops and Moly coated sides.                             $270.00 set

            Pistons are available in any oversize or compression ratio you want.

Total-Seal Piston Rings .014-.016 end gap.                                                   $179.00 set

            Plasma Moly top ring. Total-Seal second ring and Gold power oil ring.

Stock Con rods Race prepared.                                                                        $450.00 set

Shot peened. Beam polished. Big end resized. Small end bushed for floater wrist pins. ARP Rod bolts installed.

Crankshaft Race prepared.                                                                                      $480.00

            Index ground. Weights and oil passages detailed. Shot Peened.

            Heat treated.

Block Bored and honed with torque plate.                                                             $250.00

            Includes hot tank and magnaflux

Block deck surfaced.                                                                                                $50.00

ARP Main stud kit for extra block rigidity.                                                               $139.00

ARP Head stud kit.                                                                                               $129.00

Clevite77 Rod and Main bearings.                                                                      $135.00

Japanese full engine gasket set.                                                                       $199.00

HKS 1mm Stopper type gasket.                                                                         $289.00

HKS 1.2mm Bead type gasket                                                                           $159.00

Stock flywheel lightened, Surfaced, stepped, zero balanced                          $145.00

Complete rotating assembly electronically balanced                                        $165.00

 

Cylinder Head and Intake Buildup:

Head cleaned, blasted, and pressure tested before any work is performed.

DO NOT GRIND OR ALTER THE CAMS IN ANY WAY.

Nothing works better than the stock camshafts in a 7MGT. You can move the power around but you will not make more power.

Heads are Turbo Ported and polished.                                                       $650.00

Chambers are CC. d and polished.                                                                     Included

Intake manifold Match Ported to the head.                                                    Included

Stock throttle body is enlarged 5mm over stock.                                      $250.00

Intake manifold match ported to larger throttle body.                                $50.00

All new valve guides installed.                                                                     $290.00

Valves replaced as needed.                                                                                  As needed

Stainless Steel Performance Valves                                                          $19.00 ea

Heavy duty valve springs.                                                                            $210.00

3 angle racing valve job.                                                                                   $350.00

Hand lap and back-cut an all valves.                                                           included

Valves adjusted and all shim work done.                                                    $250.00

Blanchard grind head surface.                                                                         $50.00

New Timing Belt                                                                                            $32.00

Adjustable Camshaft gears ( Slider Type )                                                 $350.00 pr.

 

Complete engines are Long Block Assemblies from valve cover to oil pan including flywheel less any manifolding and external items. All complete engines have the same bore and hone work. The same 3 angle valve job. The same balancing and Clevite77 engine bearings. All get new timing belts and water pumps.

 

Stage 1 complete engine using your engine core:                          $3800.00

            Good street engine for mild modified use up to 350 HP

            Mild turbo upgrades and less than 16 psi boost.

·       Stock cast pistons with Total-Seal rings. ( $545.00 set with rings )

·       Balanced and blueprinted.

·       ARP rod bolts and head bolts.

·       A very nice much better than factory new, rebuilt engine.

           

Stage 2 complete engine using your engine core:                          $4500.00

            Stage-1 with the following changes.  

Street and strip engine for up to 450 HP

Larger turbo upgrades with 18-20 psi boost and extra fuel enrichment.

·       JE Forged Pistons and Total-Seal rings

·       ARP Head studs. HKS 2mm head gasket

·       Mild turbo port and polish.

           

Stage 3 complete engine using your engine core:                          $6200.00

Full tilt race motor. 600+ HP capable for serious drag racing and endurance road racing applications. Or, just if you are a total Speed Freak with a lot of money. Includes EVERYTHING listed in the 600+ HP section. Requires you sending us your complete intake manifold and throttle body as well as your long block engine core. To achieve these HP levels will require a programmable engine management system, 550cc or bigger injectors, 62-1 or T66 Turbo, Upgraded Intercooler and plumbing, Racing compressor bypass valve, (2) Bosch racing fuel pumps. Etc., Etc.

 

We ship engines all over the world. In the continental USA the average shipping cost for a 7MGT long block is $300.00 + a $150.00 crating charge. The cost to send the core to us is less. Call us for specific shipping information.

 

Turbo System Components:

Turbocharger upgrades:

Upgraded CT26 Turbocharger

            Uses YOUR REBUILDABLE CORE. Turns the stock CT26

            Into a 60-1 compressor with machined housing and clip

            On the Turbine wheel. Included complete rebuild and

            Dynamic balance.                                                                              $895.00

 

T04E Turbo upgrade                                                                                              Call

            Fast spooling unit for up to 450 hp applications

            Requires New exhaust manifold and external wastegate

            Ball Bearing units available

 

T04B Turbo upgrade                                                                                              Call

            Available in a variety of sizes, trims, AR. s to suit your application

            Requires New exhaust manifold and external wastegate

            Ball bearing units available

 

60-1, 62-1, T66 Turbochargers

            Call for specifics. Applications up to 800 HP

 

Fuel System Upgrades:

            Depending on what kind of HP you are trying to make and what you want to spend you have 3 viable approaches to getting fuel into your 7MGT. Using a VPC or

F-CON is not the answer.

Stage-1 Fuel System Upgrade:                                                                   $425.00

This is for those of you that are doing mild street upgrades and just need a bit more fuel.

Bosch Racing Fuel Pump

Adjustable Rising Rate Fuel Regulator

Stage-2 Fuel System Upgrades:

            For up to 450 HP while retaining the stock fuel management system.

   Option-1                                                                                                     $965.00

Bosch Racing Fuel Pump

            550cc Fuel Injector Upgrade

            Adjustable Rising Rate Fuel Regulator

More fuel all the time. Definitely affects fuel economy and everyday driveability. Also makes it pretty much impossible to pass smog. Easy install with not much to adjust but the regulator.

 

   Option-2                                                                                                     $1095.00

            Bosch Racing Fuel Pump

            2 Injector AIC System with controller and (2) 550cc fuel injectors.

           

Includes new over the valve cover pipe with the injector bosses built in.

This is a great way to do it if you want to keep the car running just like stock except when you are at high boost levels and really need the fuel. Will also pass Smog inspection. Controller is adjustable for injection starting point and

duration.

 

Stage-3 Fuel system upgrades:

            Programmable management system upgrades for all out 500+ HP systems.

These systems  require using a laptop computer to set the fuel and/or ignition curves. Both systems are complete with software, sensors, tuning manual and baseline programs. This is for those of you that want to get the most out of your 7MGT and retain good driveability. There are 2 methods. The first is to scrap the fuel and ignition system completely and use a stand alone computer to control all aspects of the engines operation( TEC-II or HALTECH E6 ). The second is to retain the stock Ignition system and curve and just control the fuel (HALTECH F9A). Both have their merits. It really depends on the gas you will be running and your how much control you want. A very heavily modified street engine running pump gas will really require the ignition control of a complete stand alone system to keep detonation under control under high boost low octane situations.

 

Individual Components:

Fuel Pump                                                                                          $269.00

Fuel Injectors

                                                                        440cc                         $85.00 ea

                                                                        550cc                         $95.00 ea

AIC Controller. ( Up to 4 extra injectors.)                                            $395.00

                          ( 6 injector controller.)                                              $850.00

Pressure regulators                                                                  

            Adjustable Rising rate boost dependent                              $219.00

            Bosch adjustable baseline regulator                                    $69.00

Electromotive TEC-II systems:                                                         $1895.00

            Systems include all needed sensors ( Less Knock and 02 sensor)

            Trigger Wheel and mag pickup. WINDOWS software license

            Programming cable and book

            Baseline program, spark plug wires, trigger wheel mounting diagram

            Optional:

            Bolt on crank trigger system using your crank pulley. Includes

            bolt on mag pick up bracket                                                         $195.00

Note: Electromotive TEC-II systems do not include wiring harness. It is a wire yourself system.

 

 

 

HALTECH F-9A System:                                                                $1195.00

Complete system with wiring harness and all needed sensors ( Less Knock and 02 sensor) Programming Software, Programming cable, Comprehensive Instruction Manual, Baseline Program.

 

T04 Exhaust manifold with Wastegate Port                                    $795.00

Spearco Intercooler Upgrade for use with stock plumbing            $795.00

HKS Racing Compressor Bypass Valve                                        $199.00

Manual Boost Controller ( Dial-A-Boost )                                        $69.00

 

HKS EVC-IV Boost controller                                                           $599.00

HKS EVC-EZ Boost Controller                                                         $395.00

HKS Turbo Timer (with harness.)                                                          $179.00

 

This is the common stuff we do to these cars. It is by no means comprehensive. We do all our own fabrication and machine work so there is very little we cannot do. If you have a specific request or want something you do not see listed, contact us.

 

 

Toyota Supra 7MGT 600+ HP:

This is the major components we use when building a 7MGT to make 600+ HP. There are quite a few other details involved but this is the big stuff.

 

Stage-3 engine as listed above

T04B Exhaust Manifold

Turbonetics T66 Ball Bearing Turbo with V-band outlet

Turbonetics Deltagate Race Gate

Electromotive TEC-II Management system

(6) 750cc fuel injectors

(2) Bosch Racing fuel pumps with ½. feed lines

Turbonetics Godzilla Bypass valve

Spearco Intercooler

2.5. plumbing in and out with 3. going over valve covers to throttle body.

3. Exhaust from Turbo to tailpipe with 3. Ultra-Flo muffler

Enlarged Stock throttle body with match ported intake

Adjustable Cam Gears